Can I Use a Round Tablecloth on a Rectangle Table

February 17, 2022 Post a Comment

Download Article

In addition to covering your dining or kitchen table, a homemade tablecloth can cover a small, round side tabular array. Depending upon the width of the fabric and the tabletop, you lot may need to sew together several widths of fabric together to make a round tablecloth. You can learn how to make a round tablecloth out of several fabrics. You can sew a tablecloth out of a mid-weight cotton or linen fabric or employ a laminated cotton wool for a wipe-off tablecloth.

Steps Download Article

one
Measure out the diameter of the tabletop. ^[one] Also mensurate the length from the tabletop to the floor if you want to make a round tablecloth that stretches to the flooring.^[ii]
- If you don't want the bootleg tablecloth to reach the floor, measure out the distance yous'd like it to fall to.^[3] For example, if you volition be sitting at the table, y'all may want the cloth to fall just above your legs.
2

Determine how much fabric you lot demand. Add the tabletop's diameter to twice the length of the finished tablecloth.

Advertisement
3

Cutting a length of fabric that measures the diameter plus twice the length, plus 1 inch (2.54 cm) for a hem.
4
Place the 2 lengths of fabric on top of each other, correct-sides facing each other. Pin the fabrics together along one long "wrong" side.^[4]
- Only practice this if your fabric is non wide plenty to cover then entire table. For example, if your tabletop is 36 inches (.91 m) across and the finished homemade tablecloth will be 18 inches (.45 thousand) long, y'all'll demand a piece of cloth that measures 72 inches (ane.83 g) square.
5

Stitch the fabrics together forth the pinned side, .5 inch (i.27 cm) away from the edge.
6

Unfold the fabrics, and iron the seam flat.
7

Trim the width of the fabric so it covers the size of the circular tablecloth plus ane inch (two.54 cm) for the hem.
8

Fold the piece of fabric in half, right side facing in. Fold it in half over again, the opposite way, so that you lot have a square of fabric one/4 the size of the original piece.^[five]
9

Set the tape measure diagonally across the folded fabric, from the folded corner to the opposite corner. Measure half the finished size of the round tablecloth from the pinnacle corner, and make a marker at that signal on the fabric.
ten

Describe a curved line from that mark to the top outer corner and some other from that marking to the bottom inner corner.
xi

Cut the material along the lines you lot merely drew. When you unfold the tablecloth fabric, you lot should have a perfect circle.
12

Atomic number 26 the circumvolve apartment to remove any creases creating by folding the fabric. ^[6]
thirteen

Hem the homemade tablecloth. Fold nether the border of the circumvolve 1/four inch (.64 cm), and fold information technology under another 3/4 inch (1.9 cm). Pin and then sew the hem.

Ad

Add New Question

Question

How much 43" wide material do I need for a 60" round table with a 13" drop?

Observe the width of the tablecloth: sixty + 13 (driblet on one side) + 13 (drop on other side) = 86". Add together an additional inch either side for hemming = 88". You will need iii lengths of textile 2.5 yards (90") long, so vii.5 yards.
Question

How much textile practise I demand for table 60 inches diameter by 66 cm loftier?

For a table lx inches in diameter with a 5-inch drop each side, your textile should exist lx inches wide.
Question

How much trim is needed to fit effectually the edges of a 60" tablecloth?

After cutting cloth every bit outlined above, fold material in one-half to form a one-half-circle. Fold that one-half-circumvolve in half to course a round-bottomed triangle. Fold that triangle in half to grade a smaller triangle. Measure out the bottom curved end of the last and smallest triangle you simply formed (make certain the fold side of the triangle you are measuring is admittedly flat, as not doing and then could bear upon your measurement) and multiply that measurement by eight. This will give yous the circumference of your tablecloth, which volition be the amount of trim you need to stop your project. I would, however, suggest you add six inches or so just in case your measurement was less than precise.
Question

How much material do I need to make a 90" round tablecloth using 56" textile with no eye seam?

You demand six yards, including a four" drib. If longer drop is desired, add 4x driblet difference to yardage before ownership. You can't avoid a center seam if the width of your fabric is less than the width of your table unless you employ i material panel 56" 10 90", plus drop, plus 1.five" for hem or fringe as the eye panel of the tablecloth.